二元氧化物修饰催化剂的制备及其自增湿性能

doi:10.19799/j.cnki.2095-4239.2021.0386

储能科学与技术 ›› 2021, Vol. 10 ›› Issue (6): 2013-2019.doi: 10.19799/j.cnki.2095-4239.2021.0386

二元氧化物修饰催化剂的制备及其自增湿性能

张博雅(), 刘柏鸿, 黎远航, 刘欣, 陈乾风, 侯三英()

南华大学化学化工学院，湖南衡阳 421001

收稿日期:2021-08-02 修回日期:2021-08-18 出版日期:2021-11-05 发布日期:2021-11-03
通讯作者: 张博雅,侯三英 E-mail:zby_librep@163.com;tysgying@163.com
作者简介:张博雅（2000—），女，本科，E-mail：zby_librep@163.com；
基金资助:
湖南省自然科学基金青年项目(2020JJ5470);湖南省教育厅青年项目(18B275);国家级大学生创新创业训练项目(S202010555034)

Binary oxide modified catalyst preparation and self-humidifying performance

Boya ZHANG(), Bohong LIU, Yuanhang LI, Xin LIU, Qianfeng CHEN, Sanying HOU()

School of Chemistry and Chemical Engineering, University of South China, Hengyang 421001, Hunan, China

Received:2021-08-02 Revised:2021-08-18 Online:2021-11-05 Published:2021-11-03
Contact: Boya ZHANG,Sanying HOU E-mail:zby_librep@163.com;tysgying@163.com

摘要/Abstract

摘要：

利用锡硅二元氧化物分别采用前修饰法和后修饰法修饰Pt/C催化剂，制备得到两种复合催化剂，并用于阳极催化层制备膜电极(MEA)。首先，考察修饰方式对膜电极性能的影响。膜电极的电池性能测试表明，使用前修饰法制备的Pt/SnO₂-SiO₂/C复合催化剂表现出更优的电池性能：在电池温度为50 ℃、完全增湿条件下，0.6 V的电流密度高达1100 mA/cm²。同时该膜电极也显示出良好的自增湿性能和稳定性：在电池温度为50 ℃、完全不增湿(干气)条件下，0.6 V的电流密度为930 mA/cm²，且经过10 h稳定性测试后，性能仅降低13%，而空白膜电极在2 h内性能下降63%。进一步比较在不同相对湿度条件下的膜电极性能，结果表明该膜电极在相对湿度较低的条件下表现出优异的自增湿性能。根据实验数据，初步推测出一种使用Pt/SnO₂-SiO₂/C复合催化剂的膜电极的自增湿机理。

关键词: 燃料电池, 催化剂, 复合材料, 锡硅二元氧化物, 低湿度

Abstract:

The Pt/C catalyst was modified by premodification and postmodification methods using tin-silicon binary oxide to prepare two composite catalysts. Furthermore, two composite catalysts were used on the anode to prepare a membrane electrode assembly (MEA). First, the influence of modification methods on the performance of MEA was investigated. The cell performance test of two MEAs demonstrated that the Pt/SnO₂-SiO₂/C composite catalyst prepared by the premodification method had better cell performance: the current density at 0.6 V is as high as 1100 mA/cm² under complete humidification at 50 ℃. At the same time, the MEA also exhibited excellent self-humidification performance and stability: the current density at 0.6 V is 930 mA/cm²at a 50 ℃ cell temperature and with no humidification (dry gas); after the 10 h stability test, the performance only decreased by 13%, while the performance of blank MEAs decreases by 63% within 2 h. Further comparisons of the MEA performance under different relative humidity conditions shows that the MEA exhibits excellent self-humidification performance under low relative humidity conditions. According to the experimental data, the self-humidification mechanism of a Pt/SnO₂-SiO₂/C composite catalyst is preliminarily speculated.

Key words: fuel cells, catalyst, composites, Sn/Si binary oxide, low humidity

中图分类号:

TM 911.4

张博雅, 刘柏鸿, 黎远航, 刘欣, 陈乾风, 侯三英. 二元氧化物修饰催化剂的制备及其自增湿性能[J]. 储能科学与技术, 2021, 10(6): 2013-2019.

Boya ZHANG, Bohong LIU, Yuanhang LI, Xin LIU, Qianfeng CHEN, Sanying HOU. Binary oxide modified catalyst preparation and self-humidifying performance[J]. Energy Storage Science and Technology, 2021, 10(6): 2013-2019.

图/表 9

表1

图1

图2

图3

图4

图5

图6

图7

图8

参考文献 21

1	CANO Z P, BANHAM D, YE S Y, et al. Batteries and fuel cells for emerging electric vehicle markets[J]. Nature Energy, 2018, 3(4): 279-289.
2	GERBEC M, JOVAN V, PETROVČIČ J. Operational and safety analyses of a commercial PEMFC system[J]. International Journal of Hydrogen Energy, 2008, 33(15): 4147-4160.
3	TEIXEIRA F C, DE SÁ A I, TEIXEIRA A P S, et al. Nafion phosphonic acid composite membranes for proton exchange membranes fuel cells[J]. Applied Surface Science, 2019, 487: 889-897.
4	KETPANG K, LEE K, SHANMUGAM S. Facile synthesis of porous metal oxide nanotubes and modified nafion composite membranes for polymer electrolyte fuel cells operated under low relative humidity[J]. ACS Applied Materials & Interfaces, 2014, 6(19): 16734-16744.
5	SAKAMOTO M, NOHARA S, MIYATAKE K, et al. Effects of incorporation of SiO₂ nanoparticles into sulfonated polyimide electrolyte membranes on fuel cell performance under low humidity conditions[J]. Electrochimica Acta, 2014, 137: 213-218.
6	BAE I, OH K H, YUN S H, et al. Asymmetric silica composite polymer electrolyte membrane for water management of fuel cells[J]. Journal of Membrane Science, 2017, 542: 52-59.
7	KETPANG K, SHANMUGAM S, SUWANBOON C, et al. Efficient water management of composite membranes operated in polymer electrolyte membrane fuel cells under low relative humidity[J]. Journal of Membrane Science, 2015, 493: 285-298.
8	SHANMUGAM S, KETPANG K, AZIZ M A, et al. Composite polymer electrolyte membrane decorated with porous titanium oxide nanotubes for fuel cell operating under low relative humidity[J]. Electrochimica Acta, 2021, 384: doi: 10.1016/j.electacta.2021.138407
9	PATEL H A, MANSOR N, GADIPELLI S, et al. Superacidity in nafion/MOF hybrid membranes retains water at low humidity to enhance proton conduction for fuel cells[J]. ACS Applied Materials & Interfaces, 2016, 8(45): 30687-30691.
10	OH K, KWON O, SON B, et al. Nafion-sulfonated silica composite membrane for proton exchange membrane fuel cells under operating low humidity condition[J]. Journal of Membrane Science, 2019, 583: 103-109.
11	WATANABE M, UCHIDA H, EMORI M. Polymer electrolyte membranes incorporated with nanometer-size particles of Pt and/or metal-oxides: experimental analysis of the self-humidification and suppression of gas-crossover in fuel cells[J]. The Journal of Physical Chemistry B, 1998, 102(17): 3129-3137.
12	LIN C L, HSU S C, HO W Y. Addition of sulfonated silicon dioxide on an anode catalyst layer to improve the performance of a self-humidifying proton exchange membrane fuel cell[J]. Functional Materials Letters, 2016, 9(2): doi: 10.1142/S1793604716500259
13	JIENKULSAWAD P, CHEN Y S, ARPORNWICHANOP A. Modifying the catalyst layer using polyvinyl alcohol for the performance improvement of proton exchange membrane fuel cells under low humidity operations[J]. Polymers, 2020, 12(9): 1865.
14	LO A Y, HUANG C Y, SUNG L Y, et al. Electrophoretic deposited Pt/C/SiO₂ anode for self-humidifying and improved catalytic activity in PEMFC[J]. Electrochimica Acta, 2015, 180: 610-615.
15	GANESAN A, NARAYANASAMY M, SHUNMUGAVEL K. Self-humidifying manganese oxide-supported Pt electrocatalysts for highly-durable PEM fuel cells[J]. Electrochimica Acta, 2018, 285: 47-59.
16	SU H N, XU L M, ZHU H P, et al. Self-humidification of a PEM fuel cell using a novel Pt/SiO₂/C anode catalyst[J]. International Journal of Hydrogen Energy, 2010, 35(15): 7874-7880.
17	LO A Y, HUANG C Y, SUNG L Y, et al. Low humidifying proton exchange membrane fuel cells with enhanced power and Pt-C-h-SiO₂ anodes prepared by electrophoretic deposition[J]. ACS Sustainable Chemistry & Engineering, 2016, 4(3): 1303-1310.
18	JUNG C Y, YI J Y, YI S C. On the role of the silica-containing catalyst layer for proton exchange membrane fuel cells[J]. Energy, 2014, 68: 794-800.
19	HOU S Y, CHEN R, ZOU H B, et al. High-performance membrane electrode assembly with multi-functional Pt/SnO₂-SiO₂/C catalyst for proton exchange membrane fuel cell operated under low-humidity conditions[J]. International Journal of Hydrogen Energy, 2016, 41(21): 9197-9203.
20	LUO F, LIAO S J, DANG D, et al. Tin and silicon binary oxide on the carbon support of a Pt electrocatalyst with enhanced activity and durability[J]. ACS Catalysis, 2015, 5(4): 2242-2249.
21	LEIMIN X, SHIJUN L, LIJUN Y, et al. Investigation of a novel catalyst coated membrane method to prepare low-platinum-loading membrane electrode assemblies for PEMFCs[J]. Fuel Cells, 2009, 9(2): 101-105.

膜电极名称	阳极	阴极
MEA 0	Pt/C (40% Pt)	Pt/C (40% Pt)
MEA 1	Pt/SnO₂-SiO₂/C (20% Pt)	Pt/C (40% Pt)
MEA 2	Pt/C-SnO₂-SiO₂ (40% Pt)	Pt/C (40% Pt)
MEA 3	Pt/C (40% Pt)	Pt/SnO₂-SiO₂/C (20% Pt)

[1]	刘长洋, 卞刘振, 郜建全, 彭继华, 彭军, 安胜利. 固体氧化物燃料电池La_0.7Sr_0.3Fe_0.9Ni_0.1O_3-_δ 对称电极的电化学性能[J]. 储能科学与技术, 2022, 11(7): 2059-2065.
[2]	谢程露, 黄贤坤, 康丽霞, 刘永忠. 胶体溶液制备碳纳米管负载钌纳米颗粒的电催化合成氨性能[J]. 储能科学与技术, 2022, 11(6): 1947-1956.
[3]	王培灿, 万磊, 徐子昂, 许琴, 庞茂斌, 陈金勋, 王保国. 基于界面工程的自支撑催化电极用于电解水制氢[J]. 储能科学与技术, 2022, 11(6): 1934-1946.
[4]	田辉, 华栋, 曼茂立, 刘春哲, 李国君, 张兄文. 板式固体氧化物燃料电池积碳特性实验[J]. 储能科学与技术, 2022, 11(5): 1314-1321.
[5]	陈健鑫, 盛楠, 朱春宇, 饶中浩. 生物质碳负载镍基纳米颗粒及其电解水析氢性能[J]. 储能科学与技术, 2022, 11(5): 1350-1357.
[6]	胡冶州, 王双, 申涛, 朱叶, 王得丽. 限域型贵金属氧还原反应电催化剂研究进展[J]. 储能科学与技术, 2022, 11(4): 1264-1277.
[7]	贾林辉, 盖泽嘉, 李沫汐, 梁华根. MOFs及其衍生物在锂-氧气电池正极中的研究进展[J]. 储能科学与技术, 2022, 11(2): 503-510.
[8]	谢林翰, 李万忠, 张倩倩, 曹高萍, 邱景义, 明海, 封伟. 植物发供电技术的研究进展[J]. 储能科学与技术, 2022, 11(2): 442-466.
[9]	郭云琪, 盛楠, 朱春宇, 饶中浩. 基于模板法制备氧化铝纤维及其石蜡复合相变材料热性能[J]. 储能科学与技术, 2022, 11(2): 511-520.
[10]	田辉, 华栋, 曼茂立, 刘春哲, 李国君, 张兄文. 板式固体氧化物燃料电池积碳特性的数值研究[J]. 储能科学与技术, 2022, 11(1): 291-296.
[11]	张诗诗, 秦棪阳, 苏亚琼. 析氢反应中氮掺杂石墨烯负载金属单/双原子催化活性起源[J]. 储能科学与技术, 2021, 10(6): 2008-2012.
[12]	吴小员, 卢新宝, 董嘉璇, 汪茹. 燃料电池汽车地方政策研究[J]. 储能科学与技术, 2021, 10(6): 1987-1997.
[13]	李月霞, 刘全兵. MXene基纳米材料在氧还原电催化中的应用[J]. 储能科学与技术, 2021, 10(6): 1918-1930.
[14]	何峰, 张静静, 陈奕君, 张建, 王得丽. 电化学氧还原反应合成H₂O₂碳基催化剂研究进展[J]. 储能科学与技术, 2021, 10(6): 1963-1976.
[15]	于旺, 孙超, 齐冀, 卞刘振, 彭继华, 彭军, 安胜利. 固体氧化物电池Sr_2-_xFe_1.5Mo_0.5O_6-_δ氧电极材料的电化学性能[J]. 储能科学与技术, 2021, 10(6): 2020-2027.

二元氧化物修饰催化剂的制备及其自增湿性能

Binary oxide modified catalyst preparation and self-humidifying performance

RichHTML

PDF

可视化

摘要/Abstract

引用本文

使用本文

图/表 9

参考文献 21

相关文章 15

编辑推荐

Metrics

本文评价