冷却塔-内嵌管式相变屋面复合降温系统的性能研究

doi:10.19799/j.cnki.2095-4239.2024.0010

摘要/Abstract

摘要：

为提高相变屋面的性能，本文提出了一种冷却塔-内嵌管式相变屋面复合降温系统。基于焓法，建立了系统的数值计算传热模型，数值研究了该系统在福州地区的热性能及节能潜力，探讨了相变材料相变温度、相变材料导热系数以及内嵌管间距的影响，并与传统的无内嵌管相变屋面进行了对比分析。研究发现，相变温度越高，复合降温系统的相变材料越容易完成凝固，但潜热利用率随相变温度的升高呈现先增加后降低的趋势。当相变温度由35 ℃升高到41 ℃时，屋面的累计冷负荷由383 kJ/m²增大到400 kJ/m²，增加了4.4%。相变材料导热系数越高、内嵌管间距越小，复合降温系统相比于传统无内嵌管相变屋面的潜热利用优势越显著。当导热系数由0.2 W/(m·K)增加到0.8 W/(m·K)时，复合降温系统的潜热利用率和屋面累计冷负荷分别增加了36.3%和5.1%，而无内嵌管相变屋面的潜热利用率和屋面累计冷负荷分别升高了33.1%和6.3%。当内嵌管间距由500 mm减少到100 mm时，复合降温系统比传统无内嵌管相变屋面的潜热利用提高率由2.7%增大到16.3%，累计冷负荷降低率由3.8%升高到10.9%。研究结果可促进建筑节能和双碳目标的实现。

关键词: 相变屋面, 冷却塔, 内嵌管, 蓄冷, 建筑节能

Abstract:

To enhance the performance of phase-change-material (PCM) slab roofs, this study proposes an integrated cooling system combining a cooling tower with a pipe-embedded PCM slab roof. Further, leveraging the enthalpy method, the study establishes a computational heat transfer model of the developed integrated cooling system. Subsequently, the thermal performance and energy-saving potential of a similar system in Fuzhou city, China, are numerically investigated. Furthermore, the impacts of the phase-change temperature and thermal conductivity of the PCM and the pipe interval are explored, and the developed system is compared with a traditional PCM slab roof without embedded pipes. The results reveal that higher phase-change temperatures of the PCM lead to more significant solidification of the PCM within the integrated cooling system. However, with increasing phase-change temperatures of the PCM, the utilization rate of the PCM's heat of fusion within the system initially increases and subsequently decreases. Specifically, increasing the phase-change temperature of the PCM from 35 ℃ to 41 ℃ leads to a corresponding rise in the accumulated cooling load of the roof from 383 kJ/m² to 400 kJ/m², presenting an increase of 4.4%. Furthermore, higher thermal conductivities of the PCM and narrower pipe intervals improve the utilization rate of the PCM's heat of fusion within the integrated cooling system compared to that within traditional PCM slab roofs without embedded pipes. Specifically, increasing the thermal conductivity of the PCM from 0.2 W/(m·K) to 0.8 W/(m·K) boosts the utilization rate of the PCM's heat of fusion and the accumulated cooling load of the roof by 36.3% and 5.1%, respectively. Conversely, the corresponding values of the traditional PCM slab roof increase by only 33.1% and 6.3%, respectively. Moreover, when the pipe interval is decreased from 500 mm to 100 mm, the utilization rate of the PCM's heat of fusion in the integrated cooling system surpasses that in the traditional PCM slab roof by 2.7%—16.3%. Concurrently, the reduction in the accumulated cooling load of the roof increases from 3.8% to 10.9%. Overall, these findings demonstrate the potential of integrated cooling systems in promoting building energy savings and contributing toward the realization of dual-carbon goals.

Key words: PCM slab roof, cooling tower, pipe-embedded, cooling energy storage, building energy saving

中图分类号:

TK 02

逯焕杰, 陈晓明, 吴智昊, 邱金友. 冷却塔-内嵌管式相变屋面复合降温系统的性能研究[J]. 储能科学与技术, 2024, 13(7): 2435-2446.

Huanjie LU, Xiaoming CHEN, Zhihao WU, Jinyou QIU. Performance of an integrated cooling system combining a cooling tower and a pipe-embedded phase-change-material slab roof[J]. Energy Storage Science and Technology, 2024, 13(7): 2435-2446.

图/表 15

图1

表1

表2

图2

图3

图4

图5

图6

图7

图8

图9

图10

图11

图12

图13

参考文献 20

1	李先庭, 赵阳, 魏庆芃, 等. 碳中和背景下我国空调系统发展趋势[J]. 暖通空调, 2022, 52(10): 75-83, 61. DOI: 10.19991/j.hvac1971. 2022.10.12.
	LI X T, ZHAO Y, WEI Q P, et al. Developing trend of air conditioning system oriented to carbon neutrality in China[J]. Heating Ventilating & Air Conditioning, 2022, 52(10): 75-83, 61. DOI: 10.19991/j.hvac1971.2022.10.12.
2	XU X H, WANG S W, WANG J B, et al. Active pipe-embedded structures in buildings for utilizing low-grade energy sources: A review[J]. Energy and Buildings, 2010, 42(10): 1567-1581. DOI: 10.1016/j.enbuild.2010.05.002.
3	ZAHIR M H, IRSHAD K, SHAFIULLAH M, et al. Challenges of the application of PCMs to achieve zero energy buildings under hot weather conditions: A review[J]. Journal of Energy Storage, 2023, 64: 107156. DOI: 10.1016/j.est.2023.107156.
4	ZHAN H X, MAHYUDDIN N, SULAIMAN R, et al. Phase change material (PCM) integrations into buildings in hot climates with simulation access for energy performance and thermal comfort: A review[J]. Construction and Building Materials, 2023, 397: 132312. DOI: 10.1016/j.conbuildmat.2023.132312.
5	鞠杰, 陈瑞芳, 魏钢. 新型相变储能材料在建筑工程中的应用[J]. 储能科学与技术, 2023, 12(12): 3883-3885. DOI: 10.19799/j.cnki.2095-4239.2023.0810.
	JU J, CHEN R F, WEI G. Application of new phase change energy storage materials in building engineering[J]. Energy Storage Science and Technology, 2023, 12(12): 3883-3885. DOI: 10.19799/j.cnki.2095-4239.2023.0810.
6	PATEL B, RATHORE P K S, GUPTA N K, et al. Location optimization of phase change material for thermal energy storage in concrete block for development of energy efficient buildings[J]. Renewable Energy, 2023, 218: 119306. DOI: 10.1016/j.renene.2023.119306.
7	YU J H, YANG Q C, YE H, et al. The optimum phase transition temperature for building roof with outer layer PCM in different climate regions of China[J]. Energy Procedia, 2019, 158: 3045-3051. DOI: 10.1016/j.egypro.2019.01.989.
8	LI Y R, LONG E S, ZHANG L L, et al. Energy-saving potential of intermittent heating system: Influence of composite phase change wall and optimization strategy[J]. Energy Exploration & Exploitation, 2021, 39(1): 426-443. DOI: 10.1177/0144598720969217.
9	周莹, 王双喜, 刘中华, 等. 基于ANSYS的日光温室复合相变保温墙体的模拟研究[J]. 太阳能学报, 2020, 41(4): 113-122. DOI: 10.19912/j.0254-0096.2020.04.018.
	ZHOU Y, WANG S X, LIU Z H, et al. Simulation study on composite phase change thermal insulation walls in solar greenhouse based on ANSYS[J]. Acta Energiae Solaris Sinica, 2020, 41(4): 113-122. DOI: 10.19912/j.0254-0096.2020.04.018.
10	JAVIDAN M, ASGARI M, GHOLINIA M, et al. Thermal energy storage inside the chamber with a brick wall using the phase change process of paraffinic materials: A numerical simulation[J]. Theoretical and Applied Mechanics Letters, 2022, 12(3): 100329. DOI: 10.1016/j.taml.2022.100329.
11	中华人民共和国住房和城乡建设部. 民用建筑热工设计规范: GB 50176—2016[S]. 北京: 中国建筑工业出版社, 2017.
	Ministry of Housing and Urban-Rural Development of the People's Republic of China. Code for thermal design of civil building: GB 50176—2016[S]. Beijing: China Architecture & Building Press, 2017.
12	陈萨如拉, 常甜馨, 杨洋, 等. 既有建筑嵌管式相变复合墙体夏季热特性研究[J]. 中国科学技术大学学报, 2021, 51(11): 840-856.
	CHEN S R L, CHANG T X, YANG Y, et al. Summer thermal performance study on pipe-embedded PCM composite wall in existing buildings[J]. Justc, 2021, 51(11): 840-856.
13	朱婷婷, 赵明, 陈昊, 等. 相变储能地板辐射供暖系统蓄热性能数值模拟[J]. 暖通空调, 2015, 45(9): 70-75.
	ZHU T T, ZHAO M, CHEN H, et al. Numerical simulation on heat storage performance of phase change energy storage floor heating system[J]. Heating Ventilating & Air Conditioning, 2015, 45(9): 70-75.
14	陈晓明. 相变储能通风与空调耦合运行性能分析及节能优化[D]. 长沙: 湖南大学, 2017.
	CHEN X M. Performance analysis and energy-saving optimization of phase change energy storage ventilation coupled with air conditioning[D]. Changsha: Hunan University, 2017.
15	VOLLER V R, PRAKASH C. A fixed grid numerical modelling methodology for convection-diffusion mushy region phase-change problems[J]. International Journal of Heat and Mass Transfer, 1987, 30(8): 1709-1719. DOI: 10.1016/0017-9310(87)90317-6.
16	XU K, XU X H, YAN T. Performance evaluation of a pipe-embedded phase change material (PE-PCM) roof integrated with solar collector[J]. Journal of Building Engineering, 2023, 71: 106582. DOI: 10.1016/j.jobe.2023.106582.
17	田国华. 相变储能建筑墙体传热特性及能耗影响研究[D]. 徐州: 中国矿业大学, 2018.
	TIAN G H. Study on heat transfer characteristics and energy consumption influence of phase change energy storage building walls[D]. Xuzhou: China University of Mining and Technology, 2018.
18	张红婴, 钟珂, 刘加平. 太阳辐射吸收系数对建筑物全年空调能耗的影响[J]. 东华大学学报(自然科学版), 2017, 43(2): 266-273. DOI: 10.3969/j.issn.1671-0444.2017.02.019.
	ZHANG H Y, ZHONG K, LIU J P. Effect of solar absorption coefficient on annual energy consumption of air-conditioning in building[J]. Journal of Donghua University (Natural Science), 2017, 43(2): 266-273. DOI: 10.3969/j.issn.1671-0444.2017.02.019.
19	杨世铭, 陶文铨. 传热学[M]. 4版. 北京: 高等教育出版社, 2006.YANG S M, TAO W Q. Heat transfer[M]. 4th ed. Beijing: Higher Education Press, 2006.
20	中国气象局气象信息中心气象资料室, 清华大学建筑技术科学系. 中国建筑热环境分析专用气象数据集[M]. 北京: 中国建筑工业出版社, 2005: 1-165.
	Meteorological Data Room, Meteorological Information Center, China Meteorological Administration, Department of Building Technology and Science, Tsinghua University. Special meteorological data set for thermal environment analysis of buildings in China[M]. Beijing: China Architecture & Building Press, 2005: 1-165.

材料	厚度/mm	导热系数/[W/(m·K)]	密度/(kg/m³)	比热容/[J/(kg·K)]	相变温度/℃	相变潜热/(J/kg)
水泥砂浆	20	0.93	1800	1050	—	—
EPS	90	0.042	30	1380	—	—
水泥砂浆	20	0.93	1800	1050	—	—
水泥炉渣	100	0.81	1700	1050	—	—
钢筋混凝土	120	1.74	2500	920	—	—
水泥砂浆	20	0.93	1800	1050	—	—
RT35HC	35	0.2	880(s) 770(l)	2000	34~36	240000
PE水管	1	0.43	920	2300	—	—

湿球温度/℃	出水温度/℃
30	31.40
28	29.63
26	27.88
24	26.15
22	24.44
20	22.75
18	21.08
16	19.43
14	17.79

[1]	黎福超, 陈明彪, 杜群, 陈永珍, 宋文吉, 林文野, 冯自平. 基于流态冰浆蓄冷的深远海风电就地消纳[J]. 储能科学与技术, 2023, 12(12): 3730-3739.
[2]	戴照峰, 姜竹, 赵东亮, 张志远, 张小松. 果蔬用冷库相变材料研制及其系统应用[J]. 储能科学与技术, 2023, 12(12): 3720-3729.
[3]	李荣, 孙志高, 宋佳. 氨基酸侧链对HCFC-141b水合物形成的影响[J]. 储能科学与技术, 2022, 11(7): 2126-2132.
[4]	吴玉庭, 寇真峰, 张灿灿, 吴伊洋. 列管式固体氯化钠蓄冷换热器动态分布参数分析[J]. 储能科学与技术, 2022, 11(6): 1988-1995.
[5]	张琦, 王玉静, 李银雷, 刘重阳. 一种新型蓄冷储热复合相变材料及其应用[J]. 储能科学与技术, 2022, 11(10): 3133-3141.
[6]	傅德坤, 宋文吉, 陈明彪, 冯自平. 跨季节蓄冷技术及在设施农业应用的经济性分析[J]. 储能科学与技术, 2021, 10(6): 2385-2391.
[7]	吴玉庭, 宋阁阁, 张灿灿, 寇真峰, 鹿院卫. 超临界压缩空气储能系统蓄冷换热器优化设计[J]. 储能科学与技术, 2021, 10(4): 1374-1379.
[8]	王俊, 曹建军, 张利勇, 刘亚奇, 凌浩恕, 徐玉杰, 王亮, 周学志, 谢宁宁, 陈海生. 基于分布式能源系统的蓄冷蓄热技术应用现状[J]. 储能科学与技术, 2020, 9(6): 1847-1857.
[9]	李国跃, 林曦鹏, 王亮, 王艺斐, 彭珑, 陈海生, 谢宁宁. 储释冷循环对岩石材料性能的影响[J]. 储能科学与技术, 2020, 9(4): 1074-1081.
[10]	童山虎, 聂彬剑, 李子潇, 金翼, 丁玉龙, 胡宏利. 基于相变蓄冷技术的冷链集装箱性能研究[J]. 储能科学与技术, 2020, 9(1): 211-216.
[11]	王汉青, 赵越. 相变储能围护结构在建筑节能中的应用[J]. 储能科学与技术, 2018, 7(S1): 75-83.
[12]	周孙希, 章学来, 刘升. 十四烷-正辛酸有机复合相变材料的制备和性能[J]. 储能科学与技术, 2018, 7(4): 692-697.
[13]	尹少武1,2，李鸿坤1，贾震雄1，王立1,2，童莉葛1,2. 冰蓄冷场合流动冰浆快速制取实验研究[J]. 储能科学与技术, 2017, 6(4): 701-707.
[14]	凌子夜，王前蒿，张正国，高学农，方晓明. 双层相变材料组合式蓄冷装置的性能研究[J]. 储能科学与技术, 2017, 6(4): 696-700.
[15]	崔艳琦. 相变材料热性能及其在室内被动式储能系统的简易计算[J]. 储能科学与技术, 2017, 6(2): 302-306.